![Curiosity's first sample drilling Curiosity's first sample drilling](http://www.nasa.gov/images/content/725705main_pia16726-946.jpg)
At the center of this image from NASA's Curiosity rover is the hole in a rock called "NASA Curiosity Rover Collects First Martian Bedrock Sample" where the rover conducted its first sample drilling on Mars. Image credit: NASA/JPL-Caltech/MSSS
› Full image and caption › See drilling animation
Download Image
› Full SizeCuriosity's First Sample Drilling
At the center of this image from NASA's Curiosity rover is the hole in a rock called "John Klein" where the rover conducted its first sample drilling on Mars. The drilling took place on Feb. 8, 2013, or Sol 182, Curiosity's 182nd Martian day of operations. Several preparatory activities with the drill preceded this operation, including a test that produced the shallower hole on the right two days earlier, but the deeper hole resulted from the first use of the drill for rock sample collection.The image was obtained by Curiosity's Mars Hand Lens Imager (MAHLI) on Sol 182. The sample-collection hole is 0.63 inch (1.6 centimeters) in diameter and 2.5 inches (6.4 centimeters) deep. The "mini drill" test hole near it is the same diameter, with a depth of 0.8 inch (2 centimeters).
Image credit: NASA/JPL-Caltech/MSSS
![An animated set of three images from NASA's Curiosity rover An animated set of three images from NASA's Curiosity rover](http://www.nasa.gov/images/content/725717main_pia16728-946.gif)
Ready, Set, Drill
An animated set of three images from NASA's Curiosity rover shows the rover's drill in action on Feb. 8, 2013, or Sol 182, Curiosity's 182nd Martian day of operations. This was the first use of the drill for rock sample collection. The target was a rock called "John Klein," in the Yellowknife Bay region of Gale Crater on Mars.This set of images was obtained by Curiosity's right front Hazard-Avoidance camera on Feb. 8, 2013, or Sol 182.
Image credit: NASA/JPL-Caltech
![Drill area, called Drill area, called](http://www.nasa.gov/images/content/725682main_pia16686-43_946-710.jpg)
Download Image
› Full SizeInvestigating Curiosity's Drill Area
NASA's Mars rover Curiosity used its Mast Camera (Mastcam) to take the images combined into this mosaic of the drill area, called "John Klein." The label "Drill" indicates where the rover ultimately performed its first sample drilling.Shown on this mosaic are the four targets that were considered for drilling, all of which were analyzed by Curiosity's instrument suite. At "Brock Inlier," data from the Alpha Particle X-ray Spectrometer (APXS) and images from the Mars Hand Lens imager (MAHLI) were collected. The target "Wernecke" was brushed by the Dust Removal Tool (DRT) with complementary APXS, MAHLI, and Chemistry and Camera (ChemCam) analyses. Target "Thundercloud" was the subject of the drill checkout test known as "percuss on rock." The target Drill was interrogated by APXS, MAHLI and ChemCam.
The scene was imaged on Sol 166, the 166th Martian day of Curiosity's work on Mars (January 23, 2013). The color has been white-balanced to show what the rocks would like if they were on Earth.
An unannotated, white-balanced version and raw-color version are also available.
Image credit: NASA/JPL-Caltech/MSSS
NASA Curiosity Rover Collects First Martian Bedrock Sample
PASADENA,
Calif. -- NASA's Curiosity rover has, for the first time, used a drill
carried at the end of its robotic arm to bore into a flat, veiny rock on
Mars and collect a sample from its interior. This is the first time any
robot has drilled into a rock to collect a sample on Mars.
The fresh hole, about 0.63 inch (1.6 centimeters) wide and 2.5 inches (6.4 centimeters) deep in a patch of fine-grained sedimentary bedrock, can be seen in images and other data Curiosity beamed to Earth Saturday. The rock is believed to hold evidence about long-gone wet environments. In pursuit of that evidence, the rover will use its laboratory instruments to analyze rock powder collected by the drill.
"The most advanced planetary robot ever designed now is a fully operating analytical laboratory on Mars," said John Grunsfeld, NASA associate administrator for the agency's Science Mission Directorate. "This is the biggest milestone accomplishment for the Curiosity team since the sky-crane landing last August, another proud day for America."
For the next several days, ground controllers will command the rover's arm to carry out a series of steps to process the sample, ultimately delivering portions to the instruments inside.
"We commanded the first full-depth drilling, and we believe we have collected sufficient material from the rock to meet our objectives of hardware cleaning and sample drop-off," said Avi Okon, drill cognizant engineer at NASA's Jet Propulsion Laboratory (JPL), Pasadena.
Rock powder generated during drilling travels up flutes on the bit. The bit assembly has chambers to hold the powder until it can be transferred to the sample-handling mechanisms of the rover's Collection and Handling for In-Situ Martian Rock Analysis (CHIMRA) device.
Before the rock powder is analyzed, some will be used to scour traces of material that may have been deposited onto the hardware while the rover still was on Earth, despite thorough cleaning before launch.
"We'll take the powder we acquired and swish it around to scrub the internal surfaces of the drill bit assembly," said JPL's Scott McCloskey, drill systems engineer. "Then we'll use the arm to transfer the powder out of the drill into the scoop, which will be our first chance to see the acquired sample."
"Building a tool to interact forcefully with unpredictable rocks on Mars required an ambitious development and testing program," said JPL's Louise Jandura, chief engineer for Curiosity's sample system."To get to the point of making this hole in a rock on Mars, we made eight drills and bored more than 1,200 holes in 20 types of rock on Earth."
Inside the sample-handling device, the powder will be vibrated once or twice over a sieve that screens out any particles larger than six-thousandths of an inch (150 microns) across. Small portions of the sieved sample will fall through ports on the rover deck into the Chemistry and Mineralogy (CheMin) instrument and the Sample Analysis at Mars (SAM) instrument. These instruments then will begin the much-anticipated detailed analysis.
The rock Curiosity drilled is called "John Klein" in memory of a Mars Science Laboratory deputy project manager who died in 2011. Drilling for a sample is the last new activity for NASA's Mars Science Laboratory Project, which is using the car-size Curiosity rover to investigate whether an area within Mars' Gale Crater has ever offered an environment favorable for life.
JPL manages the project for NASA's Science Mission Directorate in Washington.
For more about the mission, visit:
The fresh hole, about 0.63 inch (1.6 centimeters) wide and 2.5 inches (6.4 centimeters) deep in a patch of fine-grained sedimentary bedrock, can be seen in images and other data Curiosity beamed to Earth Saturday. The rock is believed to hold evidence about long-gone wet environments. In pursuit of that evidence, the rover will use its laboratory instruments to analyze rock powder collected by the drill.
"The most advanced planetary robot ever designed now is a fully operating analytical laboratory on Mars," said John Grunsfeld, NASA associate administrator for the agency's Science Mission Directorate. "This is the biggest milestone accomplishment for the Curiosity team since the sky-crane landing last August, another proud day for America."
For the next several days, ground controllers will command the rover's arm to carry out a series of steps to process the sample, ultimately delivering portions to the instruments inside.
"We commanded the first full-depth drilling, and we believe we have collected sufficient material from the rock to meet our objectives of hardware cleaning and sample drop-off," said Avi Okon, drill cognizant engineer at NASA's Jet Propulsion Laboratory (JPL), Pasadena.
Rock powder generated during drilling travels up flutes on the bit. The bit assembly has chambers to hold the powder until it can be transferred to the sample-handling mechanisms of the rover's Collection and Handling for In-Situ Martian Rock Analysis (CHIMRA) device.
Before the rock powder is analyzed, some will be used to scour traces of material that may have been deposited onto the hardware while the rover still was on Earth, despite thorough cleaning before launch.
"We'll take the powder we acquired and swish it around to scrub the internal surfaces of the drill bit assembly," said JPL's Scott McCloskey, drill systems engineer. "Then we'll use the arm to transfer the powder out of the drill into the scoop, which will be our first chance to see the acquired sample."
"Building a tool to interact forcefully with unpredictable rocks on Mars required an ambitious development and testing program," said JPL's Louise Jandura, chief engineer for Curiosity's sample system."To get to the point of making this hole in a rock on Mars, we made eight drills and bored more than 1,200 holes in 20 types of rock on Earth."
Inside the sample-handling device, the powder will be vibrated once or twice over a sieve that screens out any particles larger than six-thousandths of an inch (150 microns) across. Small portions of the sieved sample will fall through ports on the rover deck into the Chemistry and Mineralogy (CheMin) instrument and the Sample Analysis at Mars (SAM) instrument. These instruments then will begin the much-anticipated detailed analysis.
The rock Curiosity drilled is called "John Klein" in memory of a Mars Science Laboratory deputy project manager who died in 2011. Drilling for a sample is the last new activity for NASA's Mars Science Laboratory Project, which is using the car-size Curiosity rover to investigate whether an area within Mars' Gale Crater has ever offered an environment favorable for life.
JPL manages the project for NASA's Science Mission Directorate in Washington.
For more about the mission, visit:
You can follow the mission on Facebook and Twitter at:
and
NASA
Guillermo Gonzalo Sánchez Achutegui
ayabaca@gmail.com
ayabaca@hotmail.com
ayabaca@yahoo.com
Inscríbete en el Foro del blog y participa : A Vuelo De Un Quinde - El Foro!
No hay comentarios:
Publicar un comentario
Por favor deja tus opiniones, comentarios y/o sugerencias para que nosotros podamos mejorar cada día. Gracias !!!.